Quantcast
Channel: IntoFPV Forum - Portal
Viewing all 20278 articles
Browse latest View live
↧

Can't get my motors to ARM

June 5, 2017, 9:11 pm
$
0
0
Okay so this is my fist post to this forum and I can't figure out what's going on with my FC's software.  So I guess just bare with me while I write a short novel. I'm going to try to get all the info out there at once so you guys can help me faster.

Okay so I'm more or less a total noob to this hobby I have flown quads before but this is my first build. I think I bit off a little more than I could chew here but that's how you learn right? My flight controller is a SPracing f3 deluxe, the motors I'm running are Hobbymate 2204-2300kv they work great I'v tested them and I really like the motors. I'm planning on using 5x4.5x3 Props but I haven't even gotten that far. The ESCs that I'm using are Hobbypower 30 amp. I've done some reseach on them for documentation and according to the internet they are a clone of the Hobbywing 30 amp ESCs. Don't know if that will help but I'm putting it put there anyway. My PDB is a Matek Systems PDB XT60 Idon't think it realy matters but I'm putting it out there anyway. So back to the FC, I flashed it with CleanFlight and got it connected to the receiver using PWM. That all when pretty smoothly, I know they're talking because I can turn it on and see values jump around in the receiver tab of clean flight. when I plug the battery in the ESCs make the normal starting BEEP BEEP BEEP and then repeat a single beep with a 1-2 second pause in between them. I think that means that ESCs aren't getting any signal from the FC, but I'm not sure how to check/fix that if it is the case. I have tried going to the motors tab and playing with the sliders there to see if the motors do anything, but still no response. I tried it with every different ESC protocol option in the configuration tab.

So the biggest question is how do I get he motors to turn on and spin?

Thank you in advance.
↧
Search

Western Union and Bank transfers are now available to the following countries Worldwi

June 5, 2017, 10:18 pm
$
0
0
Western Union and Bank transfers are now available to the following countries Worldwide!!!

All my Transfers are processed Immediately payment has been Confirmed. You Can Pick Up Funds From Any Western union Store in Your Location. All my Transfers are done using my own offshore servers and Accounts so you have Nothing to worry about. I give you the MTCN , sender info and all cash out info in 1-2 hours.
The transaction is done by using either high limit full info cards or bank logins (depending on amount) to make a series of transfers to our exchangers who then in turn send the money to the receiver. This is done to increase the margin of safety both for us and the receiver.


CONTACT ID

MY Mail: t0mmiv3n


ICQ: 684999438


Info needed for WU transfers :-

: Full name
: City
: Country
: Valid email for sending you MTCN info etc

MTCN Will be ready for pick up in maximum 45minus after payment
Please Dont ask me for any test transfer

Prices For Western Union Online
Transfer(Eu,Uk,Asia,Canada,Us,France,Germany,Italy and Nigeria):

$2500 Transfer = $200 Charges ( Payment BTC/PM)
$3000 Transfer = $300
$4000 Transfer = $500
$5000 Transfer = $650
$7000 Transfer = $800
$1000 Transfer = $100

Note: Only 1 time transfer on 1 name in a week , if you need daily transfers then you must have to use more names .

I TRANSFER 500$=60$ FOR FIRST TIME BUYERS FOR US TO BUILD TRUST AND LOYAL TOGETHER HERE BEFORE WE MOVE ON TO BIGGER AMOUNT HOPE TO HEAR FROM YOU SOON!!!!!!

=================<<=======>>==================
=================<<======>>=================

Info needed for Bank transfers :-

1: Bank name
2: Bank address
3: Zip code
4: Account Holder
5: Account number
6: Account Type
7: Routing number

Bank transfer will take maximum 24hour to show money in your bank account...I will only do one transfer in a week on one bank account . If you need more transfers then arrange more bank accounts .


Price List For Bank Transfer:
$1600 transfer = $250 Charges (Payment BTC/PM)
$2500 Transfer = $350 Charges
$5000 Transfer = $600 Charges
$10000 Transfer = $1000
$15000 Transfer = $1500

CONTACT ID

MY Mail: t0mmiv3n


ICQ: 684999438

COME AND LET GET PAID TOGETHER AND HERE WITH GREAT BEST WORLD STUFFS IN STOCK NOW...CATCH ME ONLINE NOW...!!!!TOGETHER WE MAKE IT HAPPEN.!!
↧
↧

Western Union and Bank transfers are now available to the following countries Worldwi

June 5, 2017, 10:20 pm
$
0
0
Western Union and Bank transfers are now available to the following countries Worldwide!!!

All my Transfers are processed Immediately payment has been Confirmed. You Can Pick Up Funds From Any Western union Store in Your Location. All my Transfers are done using my own offshore servers and Accounts so you have Nothing to worry about. I give you the MTCN , sender info and all cash out info in 1-2 hours.
The transaction is done by using either high limit full info cards or bank logins (depending on amount) to make a series of transfers to our exchangers who then in turn send the money to the receiver. This is done to increase the margin of safety both for us and the receiver.


CONTACT ID

MY Mail: t0mmiv3n


ICQ: 684999438


Info needed for WU transfers :-

: Full name
: City
: Country
: Valid email for sending you MTCN info etc

MTCN Will be ready for pick up in maximum 45minus after payment
Please Dont ask me for any test transfer

Prices For Western Union Online
Transfer(Eu,Uk,Asia,Canada,Us,France,Germany,Italy and Nigeria):

$2500 Transfer = $200 Charges ( Payment BTC/PM)
$3000 Transfer = $300
$4000 Transfer = $500
$5000 Transfer = $650
$7000 Transfer = $800
$1000 Transfer = $100

Note: Only 1 time transfer on 1 name in a week , if you need daily transfers then you must have to use more names .

I TRANSFER 500$=60$ FOR FIRST TIME BUYERS FOR US TO BUILD TRUST AND LOYAL TOGETHER HERE BEFORE WE MOVE ON TO BIGGER AMOUNT HOPE TO HEAR FROM YOU SOON!!!!!!

=================<<=======>>==================
=================<<======>>=================

Info needed for Bank transfers :-

1: Bank name
2: Bank address
3: Zip code
4: Account Holder
5: Account number
6: Account Type
7: Routing number

Bank transfer will take maximum 24hour to show money in your bank account...I will only do one transfer in a week on one bank account . If you need more transfers then arrange more bank accounts .


Price List For Bank Transfer:
$1600 transfer = $250 Charges (Payment BTC/PM)
$2500 Transfer = $350 Charges
$5000 Transfer = $600 Charges
$10000 Transfer = $1000
$15000 Transfer = $1500

CONTACT ID

MY Mail: t0mmiv3n


ICQ: 684999438

COME AND LET GET PAID TOGETHER AND HERE WITH GREAT BEST WORLD STUFFS IN STOCK NOW...CATCH ME ONLINE NOW...!!!!TOGETHER WE MAKE IT HAPPEN.!!
↧

100mm 1s brushless Bat

June 5, 2017, 10:34 pm
$
0
0
Huge thanks to Sandra and BangGood who have offered to send me this quad in lieu of this Pre-Launch Article.



The Bat 100 
available to purchase here soon...

I think this little 100mm micro is pretty exciting for those (like me) wanting to make the step up from brushed motors to find out what brushless power is all about. The video at the bottom shows someone stopping one of the 56mm props by hand so we are not dealing with the high power of racing motors, but the acro flying and speed shown in the clip are not to be sniffed at, especially from a 3.7v (1s) battery!


The Bat ships PNP (Plug and Play) from BangGood and requires the installation of a ppm, SBUS or DSM receiver to fly, otherwise its fully assembled and ready to go. The Teeny1s F3 FC comes pre-flashed with OmnibusF3 running Betaflight 3.1 DShot firmware, and the 4-in-1 6A ESC send DShot 600 signals to the 0705 15000kV motors.


The FPV is provided by a 600TVL camera streaming live PAL/NTSC video through a 48 channel 25mW VTX which should provide a real-time FPV feed for well over 50m without obstructions.


As you see here, the Bat weighs in at a meager 30g dry, and with its 500mAh 30c battery is advertised with a flight time of up to 6 mins.  I hope to be getting a couple of MyLiPo.de 350mah and 600mah batteries which I will try with the bat... Expect a full review as soon as I have this one in the air!

For now check it out -
https://www.youtube.com/watch?v=_t7sjx7G5oA
↧

LIPO Internal Resistance Testing

June 5, 2017, 10:34 pm
$
0
0
Hey All,

I just got my new isdt charger today.  I decided to do an internal resistance test on all my lipos.  I should mention that I use and abuse all my packs equally and some are older than others.  

The 2 power hungry quads that use these batteries are equipped with tmotor f40 pro 2600kv and emax 2306 2400kv.  Needless to say, all these packs sag when I punch the throttle.  I have a guestimation of how many cycles have been put on each pack.  All the packs being tested were charged for about 5 minutes.  A photo is taken after 100 mah is added to the pack.

Here's some info I found on RC Groups about internal resistance:

"Based on my online research, combined with my own experience and findings, I would say, as a general rule, a per cell rating of between 0-6 mΩ is as good as it gets. Between 7 and 12 mΩ is reasonable. 12 to 20 mΩ is where you start to see the signs of aging on a battery, and beyond 20mΩ per cell, you'll want to start thinking about retiring the battery pack."



























To summarize the results,  my favourite packs to fly are infinity & adrenaline.  Both Infinity and Adrenaline packs have plenty of punch, the cells stay balanced and they are light.  I would say CNHL and BlackLabel performs about the same, both are good for the price you pay.  Dinogy Graphene packs deliver the most noticeable steady power, but they are also quite heavy.  It also looks like one of the 2 Dinogy packs that I got have a bad cell.  The one rotorev graphene is almost on it's way out, It performed well when it was new.  The multistar 1000mah lipo has the least amount of IR but has a bad cell and it's barely been used.

What I learned from all this is that paying more money does not equate to higher quality lipos.  One of the best performing lipos I've ever used are infinity graphenes. The only issue with the infinity graphene is that it came with "ST60" connectors which melted during flight!!  I had to change them to xt60.  

On the 1300mah packs, I can barely get 1 1/2 mins of flight time.  I would recommend getting 1500mah packs for anyone planning to run new generation high power motors such as emax 2306, tmotor f40pro, BH R4 etc.
↧
↧

Fried something on my FC, can power via USB but not battery

June 6, 2017, 12:05 am
$
0
0
First build here, no prior experiences with electronics and diy at this level.

I'm using OmnibusF4 pro with built in OSD + BEC. I've soldered FS-X6B transmitter and a Matek buzzer + LED to the FC and tested + configured with USB and betaflight. I'm using a Zippy compact S3, 25c 1300mah.

For power cable, I've wired battery+ to BAT+ pad, and battery- to GND pad on the FC.

When I plug in the battery for the first time, the LED on FC lighted up briefly and then died off and then there's some smoke, thou I didn't notice where exactly it is from, too busy removing the battery. 

After this point, I can no longer power the FC directly from the battery. So I tried to wired my battery directly to Matek PDB-XT60, and wired power and ground from PDB to FC. Plug in battery, the PDB LED lighted up, but nothing from the FC. 

When I plug in the USB to FC, it can power up the FC and the attached FS-X6B. And if my battery is plugged in, the voltage on betaflight shows 11v, if I unplug the battery the voltage in betaflight is 2.7v.

So question is, is there any thing I can do to power my FC with the battery? or do I need to buy a new FC?
↧

External current sensor on F4 V5 flight controller??

June 6, 2017, 1:00 am
$
0
0
Anyone here familiar with the F4 V5 PRO flight controller? (this one: https://www.banggood.com/F4-V5PRO-Flight...36342.html )

My question is how to connect an external current sensonr to the F4 V5 PRO? I have a Racerstar 4in1 30A ESC with integrated current sensor. I'd like to use the ESC current sensor instead of the FC (that way the FC board doesnt have to handle +120A of cutrent) Sadly, the FC does not have any current sensor input (unlike the F3s). I am using Betaflight, by the way.
↧

[Tut] How to fix Sp racing f3 dead gyro

June 6, 2017, 1:10 am
$
0
0
Hi recently I have couple FC that died on me so decided to spend time to fix it and succeed.


If you have Sp racing F3 that do this



Here how to fix it.

First suspect was dead Gyro/Acc

I have replaced gyro with know working one but still was no go.

Then I have replaced transistor and boom it came back to life

transistor name MIC5219  or LG33

Replace as per attached done Happy flying !!!!!

.jpg   gyro fix.jpg (Size: 417.39 KB / Downloads: 8)
↧
Search

Accucell 6 - max. charging @5.3A instead of 10A

June 6, 2017, 12:14 pm
$
0
0
hello,

so I have a question. I have the following setup to charge my lipos: Accucell 6 (80W/10A) charger (here is the HK link), a 6 way balance board and a power supply that can output 10a (just bought a new one which can also output 16A just for the problem that I am writing here about --> see also attached pic for the new setup with the same problem). I want to charge my 6x 1.550mah Tattu lipos at the same time:

6x1550mah = 9.3A --> which I set up the charger to balance charge my Lipos.

what I notice is that the charger is just indicating that it is charging only around 5.0-5.3A. and a full charge for the 6 lipos takes me almost 2h. Now the idea of the balance board was to only charge them all at around 1h and I thought that with a max output of this charger of 10A I am safe.



Can any one explain me where mistake is and why it is only charging at max. 5.3A if it can possible could go up to 10A? Is it the balance board? is there some kind of protection inside? what did I miss?

thank you very much in advance for some helpful comments.
↧
↧

Flying around buildingsite? Yes or NOOO?

June 6, 2017, 2:16 pm
↧

3s vs 4s battery

June 6, 2017, 4:24 pm
$
0
0
Hey guys,

I´m flying with a 215mm frame using 30a 4x1 ESC and Racerstar 2205-2600kv motors with 3s batteries.

I would like to buy a 4s to see the difference, and I have few  questions:

1 - Is there any setting required other than the battery settings for the alarm on Cleanflight ?
2 - What should I expect in terms of performance ? is this a huge difference ?
3 - Any hardware change required for this ?

Thanks
↧

Simulators

June 7, 2017, 5:35 am
$
0
0
Hi all. I currently have an FS ONE, Hanger 9 joystick controller for helicopters along with the software. It was good in its day but am wanting to run full version of FPV Freerider. Does anyone know if the old FS ONE controller will be compatible or do I also need to buy new simulator controller. Smile
↧

Drone for drone camp

June 7, 2017, 9:27 am
$
0
0
Hello guys,

I got to opportunity to be a member of a drone camp where young people will learn to build and fly a drone in just one week.
Now i'm looking for a drone that is almost crash resisstant and easy to build. Because of the short time and big change that not every one can solder we would like to use (bullet) connectors to make it plug and play. I was thinking of the eachine wizzard this because of his 4 mm arm thickness and easy to change the arm if one got broken. But i would like to build in some custom parts and not use the complete wizzard and I am curious about your opinion.

The shopping list:
Wizzard frame
BR2206 2200KV motors
RS30A Lite BB2 ESC
Kingkong 5040 5x4x3 props
F3 EVO Cleanflight Flight Controller for Multirotor Racing w/ 4G MicroSD
Led motor mount
Motor protector
Landing skid
Matek Systems PDB-XT60 W/ BEC 5V & 12V
Flysky FS-i6X
X6B i-BUS Receiver
↧
↧

iflight ipeaka 32bit ESCs - warning!

June 7, 2017, 1:26 pm
$
0
0
Heeeeya fellaaass,
your unlucky Mr.Magoo of FPV has stumbled once more into one of the numerous pitfalls this hobby has to offer ROFL Cry
I'd like to post a little noob-warning about the iflight ipeaka 32bit-ESCs:
I didn't know about this whole 32bit-story,
just thought *whoah! - DSHOT1200!,
and since I spontaneously didn't find any alternative and those ESCs looked neat, I ordered a couple despite the price..
..indeed, they cost pretty much the same as "the real deal", and the vendors don't indicate in any way that they're just unlicensed clones of the Airbot Wraith32, which, in turn, are just shipping the pre-orders at the moment.
Iflight (upon request) sends a pre-release version of the BLHeliSuite32, which is *sort of able to deal with the ESCs (only over USB interface). Betaflight 3.2 seems to have adapted the interface (towards non-communication with unregistered products, which is good..), though, and does not want to talk to them despite the enabled DSHOT1200 protocol. *my bad..
I've been writing back and forth for a while and trying all sorts of settings over an Arduino programmer, but no way to get the ImpulseRC F3 FC to talk to the ipeaka 32bit 35A ESCs.
Same for the 50A 32bit ESCs which I intended using on my 7inch Helix build (..which has crashed onto concrete on its maiden due to signal interference with some buggy guys who turned up all of a sudden..) - waiting for a new set of arms, *ouch..
In the meantime I had started another 6inch build, which is stalling because of the ESCs. *frustrating..
My actual favorite is the 6inch Kraken from BoltRC with F80/2200 KV motors, run with 6 x 4.5 BN biprops from HQ. Will be posting footage as soon as I find the time.. The Kraken is run by a 4-in1 35A Cicada ESC and - due to space - only a 1000 microF capacitor on the main power line (Omnibus F4 from Readytoflyquads). This setup works beautifully!

However, once again:
Listen to experienced guys like Unseen and run through their posts, their statements are golden, and I wish I had considered them earlier. Well, upon stumbling we learn..
Don't buy those ESCs, I am trying to have mine replaced right now,
unless you're dead-proficient in C programming and have a ton of time to waste..
Keep it up, everyone, and enjoy flying!
Stick to what works, for now, let's give this 32bit-story some time - at least, that's what I will do, following Unseen's word of wisdom..
↧

Improve Flying

June 7, 2017, 6:53 pm
$
0
0
What things have you all done to dramatically improve your flying?

For me, probably the number one thing I did was I got more batteries and get in a lot of flight time.  When I first started out, I would fly my one battery, charge it for an hour then fly again.  I have a big enough yard to fly at my house without having to go anywhere.  When I bumped up to 4 batteries, I found that I could get enough flight time in at one time to start making really noticeable improvements.

The second thing I did that really helped me out was putting in a bunch of hours on a flight simulator but it really doesn't compare to the real thing.  So now I feel like I'm at a bit of a plateau.  I have a good handle on the basics but I want to get to the next level so I figured I would see what others are doing in their journey.
↧
Search

Drifting

June 8, 2017, 7:02 am
$
0
0
I've been building a 250 quad for the last few weeks, which is a lot of fun. However, when I'm trying to fly it, it doesn't seem to fly as it should. When I just raise the throttle, it takes off, but not in a clean vertical way. It seems to drift, mostly to the right and the back. To my understanding, when I just use the throttle, it should take off in a perfectly vertical way?

It's a 250 quad, with an SP Racing F3 flight controller. I've balanced the props, and calibrated the ESC's and the accelerometer of the FC. 

What am I doing wrong? What could be a solution?
↧

Charge FatShark Battery

June 8, 2017, 7:30 am
$
0
0
I just got some FatShark Dom V3's  Big Grin  I knew this was going to happen!! Had to have them.

My question is how do I charge the battery.  I have a venom charger that only balance charges so that won't work.  I also have a SkyRC E4 charger but it doesn't seem to work either.  It has the banana plugs but it seems to want the balance lead plugged in to do the charging.  

Any ideas?

↧
↧

250mm Tuning

June 8, 2017, 9:56 am
$
0
0
So, as I stated in welcome section I built my first quad which is the ZMR250; I have been trying to get it more "locked-in" feeling so I can advance my skills in Acro/Rate mode. I was getting alot of sway and altitude change while trying to get it to hover; Today I tried some new props, and this log will be with some 6045 props... I really liked the way it flew with these versus the Gemfan 5030 I had on originally. I also tried some 5040 3 blade HQ props before these, but the log isn't uploaded yet. If you see anything that stands out to you, just let me know.. I may be missing something diagnostic wise that I need to work on. Gonna use this thread kind of like a timeline, as I learn more I will update my PIDs here or what I have found to help out others in the same situation. I am using BlackBox to log/attempt tuning.

ZMR 250 CF frame
BRS2205 2300kv
RS20A 4in1
FS-I6 + IA6B
SP Racing F3 FC
6045 KingKong Props
Tattu + Turnigy Nano-Tech 1300mah

Code:
# Cleanflight / SPRACINGF3 2.0.2 Apr 22 2017 / 14:55:16 (4328b13)
name ZMR250
resource BEEPER 1 C15
resource MOTOR 1 A06
resource MOTOR 2 A07
resource MOTOR 3 A11
resource MOTOR 4 A12
resource MOTOR 5 B08
resource MOTOR 6 B09
resource MOTOR 7 A02
resource MOTOR 8 A03
resource MOTOR 9 NONE
resource MOTOR 10 NONE
resource MOTOR 11 NONE
resource MOTOR 12 NONE
resource SERVO 1 NONE
resource SERVO 2 NONE
resource SERVO 3 NONE
resource SERVO 4 NONE
resource SERVO 5 NONE
resource SERVO 6 NONE
resource SERVO 7 NONE
resource SERVO 8 NONE
resource PPM 1 A00
resource PWM 1 A00
resource PWM 2 A01
resource PWM 3 B11
resource PWM 4 B10
resource PWM 5 B04
resource PWM 6 B05
resource PWM 7 B00
resource PWM 8 B01
resource LED_STRIP 1 A08
resource SERIAL_TX 1 A09
resource SERIAL_TX 2 A14
resource SERIAL_TX 3 B10
resource SERIAL_TX 4 NONE
resource SERIAL_TX 5 NONE
resource SERIAL_TX 6 NONE
resource SERIAL_TX 7 NONE
resource SERIAL_TX 8 NONE
resource SERIAL_TX 9 NONE
resource SERIAL_TX 10 NONE
resource SERIAL_TX 11 B05
resource SERIAL_TX 12 B01
resource SERIAL_RX 1 A10
resource SERIAL_RX 2 A15
resource SERIAL_RX 3 B11
resource SERIAL_RX 4 NONE
resource SERIAL_RX 5 NONE
resource SERIAL_RX 6 NONE
resource SERIAL_RX 7 NONE
resource SERIAL_RX 8 NONE
resource SERIAL_RX 9 NONE
resource SERIAL_RX 10 NONE
resource SERIAL_RX 11 B04
resource SERIAL_RX 12 B00
mixer QUADX

mmix reset

mmix 0  1.000 -1.000  1.000 -1.000
mmix 1  1.000 -1.000 -1.000  1.000
mmix 2  1.000  1.000 -1.000 -1.000
mmix 3  1.000  1.000  1.000  1.000
servo 0 1000 2000 1500 100 -1
servo 1 1000 2000 1500 100 -1
servo 2 1000 2000 1500 100 -1
servo 3 1000 2000 1500 100 -1
servo 4 1000 2000 1500 100 -1
servo 5 1000 2000 1500 100 -1
servo 6 1000 2000 1500 100 -1
servo 7 1000 2000 1500 100 -1
smix reset


feature -RX_PPM
feature -VBAT
feature -INFLIGHT_ACC_CAL
feature -RX_SERIAL
feature -MOTOR_STOP
feature -SERVO_TILT
feature -SOFTSERIAL
feature -GPS
feature -FAILSAFE
feature -SONAR
feature -TELEMETRY
feature -CURRENT_METER
feature -3D
feature -RX_PARALLEL_PWM
feature -RX_MSP
feature -RSSI_ADC
feature -LED_STRIP
feature -DISPLAY
feature -OSD
feature -UNUSED
feature -CHANNEL_FORWARDING
feature -TRANSPONDER
feature -AIRMODE
feature -SDCARD
feature -VTX
feature -RX_SPI
feature -SOFTSPI
feature -ESC_SENSOR
feature -ANTI_GRAVITY
feature INFLIGHT_ACC_CAL
feature RX_SERIAL
feature FAILSAFE
feature TELEMETRY
feature RSSI_ADC
beeper GYRO_CALIBRATED
beeper RX_LOST
beeper RX_LOST_LANDING
beeper DISARMING
beeper ARMING
beeper ARMING_GPS_FIX
beeper BAT_CRIT_LOW
beeper BAT_LOW
beeper GPS_STATUS
beeper RX_SET
beeper ACC_CALIBRATION
beeper ACC_CALIBRATION_FAIL
beeper READY_BEEP
beeper MULTI_BEEPS
beeper DISARM_REPEAT
beeper ARMED
beeper SYSTEM_INIT
beeper ON_USB
beeper BLACKBOX_ERASE
map AETR1234
serial 0 1 115200 57600 0 115200
serial 1 0 115200 57600 0 115200
serial 2 64 115200 57600 0 115200
led 0 0,0::C:0
led 1 0,0::C:0
led 2 0,0::C:0
led 3 0,0::C:0
led 4 0,0::C:0
led 5 0,0::C:0
led 6 0,0::C:0
led 7 0,0::C:0
led 8 0,0::C:0
led 9 0,0::C:0
led 10 0,0::C:0
led 11 0,0::C:0
led 12 0,0::C:0
led 13 0,0::C:0
led 14 0,0::C:0
led 15 0,0::C:0
led 16 0,0::C:0
led 17 0,0::C:0
led 18 0,0::C:0
led 19 0,0::C:0
led 20 0,0::C:0
led 21 0,0::C:0
led 22 0,0::C:0
led 23 0,0::C:0
led 24 0,0::C:0
led 25 0,0::C:0
led 26 0,0::C:0
led 27 0,0::C:0
led 28 0,0::C:0
led 29 0,0::C:0
led 30 0,0::C:0
led 31 0,0::C:0
color 0 0,0,0
color 1 0,255,255
color 2 0,0,255
color 3 30,0,255
color 4 60,0,255
color 5 90,0,255
color 6 120,0,255
color 7 150,0,255
color 8 180,0,255
color 9 210,0,255
color 10 240,0,255
color 11 270,0,255
color 12 300,0,255
color 13 330,0,255
color 14 0,0,0
color 15 0,0,0
mode_color 0 0 1
mode_color 0 1 11
mode_color 0 2 2
mode_color 0 3 13
mode_color 0 4 10
mode_color 0 5 3
mode_color 1 0 5
mode_color 1 1 11
mode_color 1 2 3
mode_color 1 3 13
mode_color 1 4 10
mode_color 1 5 3
mode_color 2 0 10
mode_color 2 1 11
mode_color 2 2 4
mode_color 2 3 13
mode_color 2 4 10
mode_color 2 5 3
mode_color 3 0 8
mode_color 3 1 11
mode_color 3 2 4
mode_color 3 3 13
mode_color 3 4 10
mode_color 3 5 3
mode_color 4 0 7
mode_color 4 1 11
mode_color 4 2 3
mode_color 4 3 13
mode_color 4 4 10
mode_color 4 5 3
mode_color 5 0 9
mode_color 5 1 11
mode_color 5 2 2
mode_color 5 3 13
mode_color 5 4 10
mode_color 5 5 3
mode_color 6 0 6
mode_color 6 1 10
mode_color 6 2 1
mode_color 6 3 0
mode_color 6 4 0
mode_color 6 5 2
mode_color 6 6 3
mode_color 6 7 6
mode_color 6 8 0
mode_color 6 9 0
mode_color 6 10 0
mode_color 7 0 3
aux 0 0 2 1900 2100
aux 1 1 0 900 1200
aux 2 2 0 1300 1700
aux 3 13 1 2000 2100
aux 4 0 0 900 900
aux 5 0 0 900 900
aux 6 0 0 900 900
aux 7 0 0 900 900
aux 8 0 0 900 900
aux 9 0 0 900 900
aux 10 0 0 900 900
aux 11 0 0 900 900
aux 12 0 0 900 900
aux 13 0 0 900 900
aux 14 0 0 900 900
aux 15 0 0 900 900
aux 16 0 0 900 900
aux 17 0 0 900 900
aux 18 0 0 900 900
aux 19 0 0 900 900
adjrange 0 0 0 900 900 0 0
adjrange 1 0 0 900 900 0 0
adjrange 2 0 0 900 900 0 0
adjrange 3 0 0 900 900 0 0
adjrange 4 0 0 900 900 0 0
adjrange 5 0 0 900 900 0 0
adjrange 6 0 0 900 900 0 0
adjrange 7 0 0 900 900 0 0
adjrange 8 0 0 900 900 0 0
adjrange 9 0 0 900 900 0 0
adjrange 10 0 0 900 900 0 0
adjrange 11 0 0 900 900 0 0
adjrange 12 0 0 900 900 0 0
adjrange 13 0 0 900 900 0 0
adjrange 14 0 0 900 900 0 0
rxrange 0 1000 2000
rxrange 1 1000 2000
rxrange 2 1000 2000
rxrange 3 1000 2000
vtx 0 0 0 0 900 900
vtx 1 0 0 0 900 900
vtx 2 0 0 0 900 900
vtx 3 0 0 0 900 900
vtx 4 0 0 0 900 900
vtx 5 0 0 0 900 900
vtx 6 0 0 0 900 900
vtx 7 0 0 0 900 900
vtx 8 0 0 0 900 900
vtx 9 0 0 0 900 900
rxfail 0 a
rxfail 1 a
rxfail 2 a
rxfail 3 a
rxfail 4 h
rxfail 5 h
rxfail 6 h
rxfail 7 h
rxfail 8 h
rxfail 9 h
rxfail 10 h
rxfail 11 h
rxfail 12 h
rxfail 13 h
rxfail 14 h
rxfail 15 h
rxfail 16 h
rxfail 17 h
set align_gyro = DEFAULT
set gyro_lpf = OFF
set gyro_sync_denom = 4
set gyro_lowpass_type = PT1
set gyro_lowpass = 90
set gyro_notch1_hz = 400
set gyro_notch1_cutoff = 300
set gyro_notch2_hz = 200
set gyro_notch2_cutoff = 100
set moron_threshold = 48
set align_acc = DEFAULT
set acc_hardware = AUTO
set acc_lpf_hz = 10
set acc_trim_pitch = 0
set acc_trim_roll = 0
set align_mag = DEFAULT
set mag_hardware = NONE
set mag_declination = 0
set magzero_x = 0
set magzero_y = 0
set magzero_z = 0
set baro_hardware = NONE
set baro_tab_size = 21
set baro_noise_lpf = 600
set baro_cf_vel = 985
set baro_cf_alt = 965
set mid_rc = 1500
set min_check = 1100
set max_check = 1900
set rssi_channel = 10
set rssi_scale = 30
set rssi_invert = OFF
set rc_interp = AUTO
set rc_interp_ch = RP
set rc_interp_int = 19
set fpv_mix_degrees = 0
set max_aux_channels = 14
set serialrx_provider = IBUS
set sbus_inversion = ON
set spektrum_sat_bind = 0
set spektrum_sat_bind_autoreset = 1
set airmode_start_throttle = 1350
set rx_min_usec = 996
set rx_max_usec = 2115
set input_filtering_mode = OFF
set blackbox_rate_num = 1
set blackbox_rate_denom = 1
set blackbox_device = SPIFLASH
set blackbox_on_motor_test = OFF
set min_throttle = 1000
set max_throttle = 1980
set min_command = 1010
set digital_idle_value = 459
set use_unsynced_pwm = OFF
set motor_pwm_protocol = DSHOT150
set motor_pwm_rate = 480
set motor_pwm_inversion = OFF
set thr_corr_value = 0
set thr_corr_angle = 800
set failsafe_delay = 10
set failsafe_off_delay = 10
set failsafe_throttle = 1000
set failsafe_kill_switch = OFF
set failsafe_throttle_low_delay = 100
set failsafe_procedure = DROP
set align_board_roll = 2
set align_board_pitch = 0
set align_board_yaw = 90
set gimbal_mode = NORMAL
set bat_capacity = 1500
set vbat_max_cell_voltage = 43
set vbat_min_cell_voltage = 33
set vbat_warning_cell_voltage = 37
set vbat_hysteresis = 1
set current_meter = ADC
set battery_meter = ADC
set bat_detect_thresh = 55
set use_vbat_alerts = ON
set use_cbat_alerts = OFF
set cbat_alert_percent = 10
set vbat_scale = 111
set ibata_scale = 400
set ibata_offset = 0
set ibatv_scale = 0
set ibatv_offset = 0
set beeper_inversion = ON
set beeper_od = OFF
set beeper_frequency = 0
set yaw_motors_reversed = OFF
set 3d_deadband_low = 1406
set 3d_deadband_high = 1514
set 3d_neutral = 1460
set 3d_deadband_throttle = 50
set servo_center_pulse = 1500
set servo_pwm_rate = 50
set servo_lowpass_hz = 0
set tri_unarmed_servo = ON
set channel_forwarding_start = 4
set reboot_character = 82
set serial_update_rate_hz = 100
set accxy_deadband = 40
set accz_deadband = 40
set acc_unarmedcal = ON
set imu_dcm_kp = 2500
set imu_dcm_ki = 0
set small_angle = 25
set auto_disarm_delay = 5
set disarm_kill_switch = ON
set gyro_cal_on_first_arm = OFF
set gps_provider = NMEA
set gps_sbas_mode = AUTO
set gps_auto_config = ON
set gps_auto_baud = OFF
set gps_wp_radius = 200
set nav_controls_heading = ON
set nav_speed_min = 100
set nav_speed_max = 300
set nav_slew_rate = 30
set fixedwing_althold_reversed = OFF
set alt_hold_deadband = 40
set alt_hold_fast_change = ON
set deadband = 5
set yaw_deadband = 5
set yaw_control_reversed = OFF
set pid_process_denom = 2
set tlm_switch = OFF
set tlm_inversion = ON
set tlm_halfduplex = ON
set frsky_default_lat = 0
set frsky_default_long = 0
set frsky_gps_format = 0
set frsky_unit = IMPERIAL
set frsky_vfas_precision = 0
set frsky_vfas_cell_voltage = OFF
set hott_alarm_int = 5
set pid_in_tlm = OFF
set ibus_report_cell_voltage = OFF
set ledstrip_visual_beeper = OFF
set osd_units = METRIC
set osd_rssi_alarm = 20
set osd_cap_alarm = 500
set osd_time_alarm = 10
set osd_alt_alarm = 100
set osd_vbat_pos = 2092
set osd_rssi_pos = 2088
set osd_flytimer_pos = 2081
set osd_ontimer_pos = 2102
set osd_flymode_pos = 2413
set osd_throttle_pos = 2273
set osd_vtx_channel_pos = 2425
set osd_crosshairs = 2248
set osd_horizon_pos = 2248
set osd_current_pos = 2433
set osd_mah_drawn_pos = 352
set osd_craft_name_pos = 2442
set osd_gps_speed_pos = 2266
set osd_gps_lon = 2546
set osd_gps_lat = 2514
set osd_gps_sats_pos = 2099
set osd_altitude_pos = 2295
set osd_pid_roll_pos = 2470
set osd_pid_pitch_pos = 453
set osd_pid_yaw_pos = 2535
set osd_power_pos = 2369
set osd_pidrate_profile_pos = 2393
set osd_battery_warning_pos = 2377
set osd_avg_cell_voltage_pos = 2124
set task_statistics = ON
set debug_mode = NONE
set displayport_msp_col_adjust = 0
set displayport_msp_row_adjust = 0
profile 1

set d_lowpass_type = BIQUAD
set d_lowpass = 100
set d_notch_hz = 260
set d_notch_cut = 160
set vbat_pid_gain = OFF
set pid_at_min_throttle = ON
set anti_gravity_thresh = 350
set anti_gravity_gain = 1000
set setpoint_relax_ratio = 100
set d_setpoint_weight = 60
set yaw_accel_limit = 100
set accel_limit = 0
set iterm_windup = 50
set yaw_lowpass = 0
set pidsum_limit = 500
set pidsum_limit_yaw = 400
set p_pitch = 58
set i_pitch = 55
set d_pitch = 40
set p_roll = 49
set i_roll = 45
set d_roll = 35
set p_yaw = 70
set i_yaw = 45
set d_yaw = 20
set p_alt = 50
set i_alt = 0
set d_alt = 0
set p_level = 50
set i_level = 50
set d_level = 100
set p_vel = 55
set i_vel = 55
set d_vel = 75
set level_sensitivity = 55
set level_limit = 55
set gps_pos_p = 15
set gps_pos_i = 0
set gps_pos_d = 0
set gps_posr_p = 34
set gps_posr_i = 14
set gps_posr_d = 53
set gps_nav_p = 25
set gps_nav_i = 33
set gps_nav_d = 83
rateprofile 0

set rc_rate = 80
set rc_rate_yaw = 85
set rc_expo = 0
set rc_yaw_expo = 0
set thr_mid = 50
set thr_expo = 0
set roll_srate = 70
set pitch_srate = 70
set yaw_srate = 70
set tpa_rate = 20
set tpa_breakpoint = 1650

#


http://hobbylp.com/wp-content/uploads/20...111408.zip
↧

new channel teaser 3.0

June 8, 2017, 11:39 am
$
0
0
it was time for an other teaser it is quit fun to make this short teaser Smile

↧

Lizard 95 is no ground dweller!

June 8, 2017, 2:12 pm
$
0
0
So I ordered an Eachine Lizard 95, FrSky version and it arrived today...too excited!!!  Anyway, I placed the battery (550mah, 3s) on the charger (11.66 volts out of the box according to my charger) and made it whole.  12.65 is topped off.

Bound it to my Taranis Q7x without any issue.  Shut everything down and cabled it to Betaflight, version 3.1.0.  Set the unit up Stock PIDs and a switch for arming set, it was time to test motors and such.  Removed the propellers when I first took it out of the box (it comes with two sets) and armed it for the first time.  Cool leds in the back create kind of a Christmasy feel!  Everything seemed to work so propellers went back on and tested it with a hover.  This unit is truly a little monster and the various videos around the interweb barely give it justice!

Anyway, this should certainly keep me busy as I work on the one I am building.

I have a second one coming in a few days, same as the one that arrived today due to a mixup in ordering if anyone is interested in purchasing one.  FrSKY version, it is NIB.  Paid $126 for it.  Would like to get what I paid for the 'spare one'.



This is after sending it around the yard and feeling completely out of control flying!  Fast and super quick.  It is going to take some getting used to.



The fun zone!



Here is the Lizard next to my E010s.
↧
Viewing all 20278 articles
Browse latest View live
Search